Blower Drive Service: We Deliver Horse Power! - Blower Drive Systems, Blower Kits, Blower Cams, Custom Carb Service

| |

REQUEST OUR CATALOG

Blowers

All BDS Blowers are assembled by hand with heavy duty competition components. The same parts used to assemble our racing blowers are the same parts used in all of our blowers. Heavy duty bearings and special double lipped teflon seals are used to ensure long life. The heavy duty bearing plates and cases are machined to precise specifications that produce the most efficient blower possible. All BDS blowers are fully show polished as a standard feature. Unpolished blowers are special order.

Blower Efficiency and Specific Blower Applications

In order for a supercharger to perform up to its maximum potential, it must be assembled, clearanced, and setup specifically for the application for which it will be used. BDS categorizes these differences by "Stages". Specify which Stage suits your requirements when you place your order or let the experts at BDS determine the correct Stage for you. CAUTION: failure to follow the guidelines outlined below could result in blower failure. BDS is not responsible for failures due to the improper use of blowers. The different Stages and their intended uses are as follows:

Stage 1
Used in almost all street applications using "pump gas". Capable of producing a maximum of 12-15 lbs. Of boost in most systems, not exceeding engine speeds in excess of 7000 RPM.

Stage 2
Used in high performance street systems, bracket racing, marine and/or dirty racing environments using high octane gas. The interior of the blower is hard anodized for added strength and efficiency. Capable of producing 15 lbs. Of boost and more on engines turning in excess of 7500 RPM.

Stage 3
Used for high performance racing applications on gas. Hard anodized and Teflon stripped on the lips of the rotors. This blower is capable of very high boost levels and high engine RPM. Designed for street, strip and off shore systems.

Stage 3.5
Same as stage 3 but utilizes billet rotors for a higher efficiency and a longer life between restripping.

Stage 4
Used for high performance racing applications using alcohol and/or nitro-methane for fuel. Hard anodized and stripped with both Nylatron and Teflon, this blower is capable of extremely high boost levels and engine RPM's. Intended for competition use only.

Stage 4.5
Same as stage 4 but utilizes bilet rotors for a higher efficiency and a longer life between restripping. This blower is front discharged for maximum performance.


Results 1 - 10 of 59	Page 1 of 6

pages ( 1 2 3 4 5 6 )next

PICTURE	PART #	DESCRIPTION	PRICE
	1071HA-AL	1071 STAGE 2, BLOWER, AIR-LOC, POLISHED, BILLET END PLATES	$3186.39
	1071HAT-AL	1071 STAGE 3, BLOWER, AIR-LOC, POLISHED, BILLET END PLATES	$3611.39
	1071HAT-FD	BDS 1071 STG 3, FRONT DISCHARGE BILLET BLOWER, BILLET PLATES,POLISHED	$4014.39
	1071HATT-AL	1071 STG 4 STD DISC BLOWER, AIR-LOC, POLISHED, BILLET PL	$3781.39
	1071HATT-FD	BDS 1071 STG 4 FRONT DISC BLOWER, AIR-LOC, BILLET PLATES,POLISHED	$4184.39
	1471HA-AL	1471 STAGE 2 BLOWER, AIR-LOC, POLISHED, BILLET END PLATES	$3486.39
	1471HAT-AL*	1471 STAGE 3,STD DISC BLOWER,AIR-LOC,POLISHED, BILLET PLATES	$3911.39
	1471HAT-FD	1471 STAGE 3 FRONT DISCHARGE BILLET AIR-LOC BLOWER, BILLET PALTES POLISHED	$4314.39
	1471HATT-AL	1471 STAGE 4., STD DISC BLOWER,AIR-LOC,BILLET END PLATES	$4081.39
	1471HATT-FD	BDS 1471 STAGE 4, FRONT DISC BLOWER,AIR-LOC, BILLET PLATES POLISHED	$4484.39

Blower Kits

Drive Kits & Components

Intake Manifolds

Blower Cams

Blowers

Custom Carb Service & Accessories